How to fibreglass a pond

13.07.2020 By Keran

how to fibreglass a pond

Aug 22,  · Fiberglass usually comes in cloth-like sheets that you can apply with a resin. If you want to fiberglass a pond, you'll have to prepare the materials properly, lay the fiberglass sheets, and finish the pond with a shiny black finish called a flow coat. 95%(62). Apr 02,  · Good luck to you if you try to replicate what you see in this video. It is not intended to be a tutorial on how to fibreglass stuff. I make it look easy bec.

A pond is constructed with a reinforced concrete base and with reinforced concrete block walls, and is rendered to provide a flat fibreglsas for the fibreglass to be laminated onto. The corners within the pond should be given a slight radius so that the fibreglass sits properly, and the surfaces should opnd checked to make sure that they are free from sharp points and lumps will make it much more difficult to lay the fibreglass matting onto.

When all the structural work is completed, the render is left to dry out completely, it is a good idea to use some sort of covering to put over the pond to protect the render from further water absorption if any bad weather occurs, make sure you plan how to sync google contacts with icloud work within a dry weather spell, do not attempt to fiberglass too colder or damp climates as this will inhibate curing process, if you are unsure please ask.

Before starting please ensure that you read all health and safety advice labels on the materials you use, protective clothing how to clear my lungs from smoking be worn such as overalls, rubber gloves, goggles and dust masks for sanding.

Plan flbreglass course of lay-up before starting, if you are working on a deep pond, leave a dry section to climb how to change ram usage in windows 7 and out from and finish this area last. Leave these layers to cure. Once the render is complete and dry you will be in a position to start work.

Apply a coat of G4, not only to seal the cement render but also to provide a bonding primer for the polyester resin. Its use as a sealer is to prevent any residual moisture and alkali present in the cement render from affecting the polyester resin.

Polyester resins are not adhesives, and whilst they do or do not bond to many tto G4 increases the adhesion due to its chemical similarity. However whilst applying G4 is by far the better system, many ponds have been constructed successfully without, simply using catalyzed resin thinned with styrene to seal the porosity in the render.

This is purely your choice dependent upon your budget. Once the G4 sealer has cured, within 4 hours applying tacky to touchlayers of c. After mixing catalyst thoroughly into resin, paint a coat onto working area then place fibreglass matting over, then paint resin over, using a paddle roller, roll over area, flattening matting and eliminating any air pockets, stipple any rouge strands into place.

Apply first layer over surface overlapping each layer by approximately 3 inches, then what is autofill on itunes second layer again with 3 inches over-lap but stagger the joints away from that of the first application, best method is how to eliminate dog urine odor in carpet wet-on-wet, if you do leave laminate for more than 24 hours make sure you abrade and wipe with acetone to sensitize surface.

When the layers of g matting and resin have cured, sand down any rough or sharp protrusions and check for dry mat or gaps, once any defects are removed or repaired wipe with acetone then apply a layer of surface tissue, this gives a smooth even finish onto the course fibrous chopped strand matting and creates a good surface for applying the flowcoat.

Make sure you apply at recommended thickness howw. It is highly important that you mix the main tin for a good 10mins or more prior to decanting batches to ensure the wax in the flowcoat has not separated whilst in transit or when stored. Although some suppliers and video guides out there show flowcoat being applied by roller, we only recommend applying ours by brush.

If the flowcoat is applied too thin, the coat will not be thick enough to hold enough wax content therefore you will end up with tacky areas, our flowcoat is a BRUSH flowcoat. Do NOT apply multiple layers of flowcoat as it will not allow secondary fibrglass, always apply a good liberal coat first time.

You can choose from a wide variety of colours, most common is British racing green for a more natural feel, black is a good colour for quite shallow nature ponds as it gives the illusion of depth. It is advisable to fill and empty the pond with water several times to bring out any toxins present. Introduce plant life first, a few weeks later if all looks well introduce the fish. This advice and information is given in good faith for guidance only.

To reassure our customers - all materials supplied by East Coast Fibreglass Supplies are of the finest quality, manufactured by companies such as Scott Bader, DSM, Owens Corning to name but a few, who all have supplied materials into the Composites industry for many years on a global scale. Samples from every batch manufactured are retained for testing, should the need arise.

Login View Cart 0 Checkout. Toggle navigation Menu. Fibreglass Pond Construction. All Rights Reserved. Shopping Lond 0 Items. Your shopping cart is currently empty. Continue Shopping Checkout.

Fibreglass Pond Construction

Jun 30,  · Only 2kg of resin should be mixed in at a time to prevent it going hard. 2kg of resin will be enough for 2m2 of fibreglass. Apply the mixed resin onto the surface of the pond with paintbrush or roller and then apply the first layer of chopped strand mat. More resin shall then be applied to the matting to ensure it is completely saturated. Aug 17,  · Fibreglassing As you can probably tell from the quality of the video quality this is an old video. Imagine what the quality would have been like if I'd have. Fibreglass Pond Construction A pond is constructed with a reinforced concrete base and with reinforced concrete block walls, and is rendered to provide a flat surface .

Last Updated: December 1, References. This article was co-authored by Scott Johnson. He has over 30 years of experience in the pool and landscape construction industry and specializes in large estate outdoor environment construction projects.

There are 12 references cited in this article, which can be found at the bottom of the page. This article has been viewed 25, times. A fiberglass finish on the interior of a pond can improve a pond's durability and is superior to concrete or plaster.

Fiberglass usually comes in cloth-like sheets that you can apply with a resin. If you want to fiberglass a pond, you'll have to prepare the materials properly, lay the fiberglass sheets, and finish the pond with a shiny black finish called a flow coat.

If done properly, fiberglassing can improve the appearance and durability of your pond. To fiberglass a pond, you'll need fiberglass cloth, epoxy or polyester resin, and some flowcoat. First, you'll want to cut the fiberglass cloth into strips that will fit in your pond. Then, you'll need to apply the resin to the sides and bottom of the pond and press the fiberglass cloth strips into it. You should apply 3 coats of fiberglass cloth and then let everything dry.

Once it's dry, you'll need to sand the surface of the fiberglass to get rid of any bumps and imperfections. Finally, you can use a paint roller to apply a coat of flowcoat over the fiberglass. To learn how to mix resin and flowcoat for your project, keep reading!

Did this summary help you? Yes No. Log in Social login does not work in incognito and private browsers. Please log in with your username or email to continue. No account yet? Create an account. Edit this Article. We use cookies to make wikiHow great.

By using our site, you agree to our cookie policy. Cookie Settings. Learn why people trust wikiHow. Download Article Explore this Article parts. Things You'll Need. Related Articles.

Article Summary. Part 1 of Purchase fiberglass cloth, resin, and flowcoat. You can buy the materials you need to fiberglass your pond from the hardware store or online. The typical fiberglass used for ponds is a g chopped strand mat. This fiberglass is durable enough to retain the water from a pond.

Purchase an epoxy or polyester resin when you buy the fiberglass sheets. Flowcoat looks like paint and comes in a variety of colors. Adding a layer of flowcoat over the fiberglass is the finishing touch for your project and will make the walls of your pond shiny and smooth. Apply the tape so that it wraps around the entirety of the pond's perimeter. Wear gloves when handling fiberglass. A thick pair of rubber gloves will stop the fiberglass from agitating your skin and will prevent you from damaging the fiberglass cloth.

Wear a respirator when working on an indoor pond. Wearing the proper gear will prevent you from inhaling the toxic fumes from the resin and particles from the fiberglass sheets. Measure the walls and floor of your pond. Measure the height of the pond's walls. Then, take the width and length measurements of the pond's floor.

This will help you determine how much fiberglass cloth you need. The surface area of a wall or floor is the length multiplied by the width. Write down the measurement so that you know the dimensions of your pond. If you need irregular or curved portions of the pond, use a tape measure and break the pond into separate 5 by 5 feet 1. Once you get the surface area of all parts of your pool, add them together to get how much fiberglass cloth you need.

Measure the fiberglass cloth. Fiberglass cloth will usually come in a roll that you can purchase online or at a hardware store. Carefully roll out the fiberglass and measure it so that it's 5—8 inches 13—20 cm longer than the height of your walls. This additional slack will lay on the outer lip and the floor of the pond. Cut the fiberglass cloth with a rolling cutter or fiberglass scissors.

Purchase a rolling cutter or fiberglass scissors at an art and crafts store or online. Cut out the sheets to your measurements. Mix your resin according to the instructions. Many epoxy resins will also come with a hardener that you must mix with the resin.

Read the instructions on the package so that you know how to mix them properly. You can purchase the resin at hardware stores or online. Part 2 of Apply the resin to the wall with a brush or roller.

Saturate a brush or roller into the resin. Apply it to the wall on the wall in long, horizontal strokes. Break up your work into 5 by 5 feet 1. Working in smaller portions will help you manage the entire project and will prevent the resin from drying out while you work.

Lay a sheet of fiberglass cloth over the resin. Apply more resin to the top of the fiberglass cloth. Saturate your brush again and apply the resin over the top of the fiberglass sheets in long horizontal motions. The sheets should become transparent once saturated. Lay a second and third sheet of fiberglass cloth over the first one. Drape another sheet of fiberglass over the first sheet. Press against the second layer of fiberglass and get the wrinkles out of it and apply another coat of resin over that cloth.

Repeat the steps until there are three coats of fiberglass cloth on the walls. Repeat the steps until all of the walls are covered in fiberglass. Continue to apply the fiberglass to the walls of your pond until all of them have been covered in three layers of fiberglass.

Repeat the process to fiberglass the floor. Once all of the walls and the floor has fiberglass applied, you'll be done applying the fiberglass cloth. Let the resin dry for two hours. Cover the pond with a tarp so that dirt and other debris doesn't get stuck to the resin. Once you've given the fiberglass time to dry, you can apply the flowcoat. Part 3 of Sand the surface with 80 grit sandpaper. Sand over the surface of the fiberglass cloth once it has dried.

You don't want to sand through the fiberglass cloth, but you do want to sand off bumps and imperfections. Mix the Flowcoat. You will usually have to mix a catalyst with the flowcoat before applying it to the walls. Read the instructions on the back of the flowcoat and mix it until it reaches a paint-like viscosity. Spread Flowcoat onto the fiberglass with a brush or roller.

Use a roller or a brush and spread the flowcoat in horizontal, then vertical strokes. Cover the walls, then the floor of the pond. The flowcoat should look like a dark black paint. Work in 5 by 5 feet 1.

Working in smaller sections will help you manage the flowcoat and help you achieve equal coverage. Lay a tarp over the pond and let the flowcoat dry. Allow the flowcoat to dry for a full 72 hours.