How to build a display case11.06.2021
DIY Display Case
Aug 25, · Tap to unmute. If playback doesn't begin shortly, try restarting your device. You're signed out. Videos you watch may be added to the TV's watch . Oct 17, · The first step is to measure the item you want to display. You need to measure the depth width and height of the item. This will give you the general idea of how big your case will have to be. When choosing your wood make sure you leave about a quarter of an inch to a half inch in the back for the battery pack for the lights.
Last Updated: July 2, References. To create this article, 10 people, some biuld, worked to edit and improve it over tp. This article has been viewedtimes. Learn more This article explains how to build a flag display case that can be used to safely caze and display valuable flags. Log in Social login does not work in incognito and private browsers.
Please log in with your username or email to continue. No account yet? Create an account. Edit this Article.
Measure the folded what time zone is nigeria using. You will need the bottom horizontal measurement along with the two diagonal measurements.
Also, get the thickness of the folded flag. Decide on the type of wood you will be using. Hardwoods are a better choice for this project.
This is for reasons of ro appeal and longevity. For this example, we will how to change passwords in keychain oak. Buy an 8 foot 2. To cut the wood, and seeing that the flag is triangular in shape, cut the angles on a 45 degree. You can do this with bild circular saw or a chop saw miter saw. You should have approx. As you know, wood has a grain pattern.
What follows now will dksplay your case more of a professional look. Measure off the longest portion of the angled 6' board that's your long point of that particular angle, the other is the short point of that particular angle. However, you will be cutting it 3" longer than that for mistakesso lets just cut our side pieces 20" long.
Measure off the 6' board from long point 20". Using a speed square or framing square, make a mark and cut your piece. Your objective now is to turn that piece around degrees, and cut the short point again in order to make it a long point.
Once you do this, your two 45 degree angles at the top of the display case will fit and the grain will match. Match up all the angled pieces until you find that grain match. When you place the bottom piece up to the angled side pieces to form the triangle, you will notice that the side pieces are too long.
Just pencil mark the bottom where it hangs over the bottom piece. That now is going to be cut at a 45 degree. Make sure buildd cut the 45 degree angle the correct way, your end sisplay should be a short to short angled piece. If it helps; when you are marking the piece to be cut, also mark the side of the board so you know for sure, which way hos wood should be cut.
Tack the frame together casr use a strap to hold it in position. Measure the size of glass you will need. Cut this to fit the outside of the triangular frame you just made. Inset glass involves using a table saw. If you have one or can use one, this is what you do. If you know at the beginning that you will be insetting the glass, then cut the entire 8' length of board at one time.
It's very difficult to cut small pieces like this and have it turn out correctly. If you have never used a table saw, ask someone that has to preform this next step. Take the piece or pieces and with the table saw in operation, slowly bukld the piece along the guide.
There are jigs out there that can be purchased for just this job. Call a do-it-yourself place. Once you have your cuts made, you are ready what is cts.
vresp. com nail it together. This is much easier done if you have a brad gun. Also place the frame so the glass is face down, so it doesn't break if it falls out during this process.
Cut this out for the backing of your display case. For oak, you can use minwax-colonial maple or early American. The top corner is a degree angle, so the ends of the pieces should each get a degree cut, but the bottom two angles themselves are each 45 degrees, therefore the cut must be half of 45 degrees, correct? The degree angle at the top is made with two degree cuts. The degree angles at the bottom edges are each made hod two Yes No. Not Helpful 3 Helpful 4. Include your email address to get a message when cqse question is answered.
By using this service, some information may be shared with YouTube. Submit a Tip All tip submissions are ho reviewed before being published. Related wikiHows How to. How to.
Introduction: Cheap and Easy Display Case
I was looking for a way to display some of my vintage transformer figures my wife got me for Christmas along with the poster and couldn't find anything that hung on the wall for a reasonable price. The solution presented itself, just make a display case. Since this one is already complete I don't have a ton of photos for the construction.
I'm currently building another that is a little different and I'll upload an update with more pictures and the changes when its done. The first step is to measure the item you want to display. You need to measure the depth width and height of the item. This will give you the general idea of how big your case will have to be. When choosing your wood make sure you leave about a quarter of an inch to a half inch in the back for the battery pack for the lights.
I used a jigsaw to cut mine my table saw is broke at the moment. You need to cut two pieces the same length for the top and two the same for the side.
Make sure to measure twice and cut once. After cutting sand the edges and check for for length accuracy. If you cut one shorter you will have to adjust for the difference on the other one.
Nail or staple the sides to the top and bottom. The easiest way is to line up the edges flush and place one nail or staple in the center. Once all sides are attached I then placed a nail in each corner making sure to keep it flush with the edge. After the nails are in I used a small square to make sure it is at right angles then placed a small bead of wood glue in each corner going being it with the square to make sure it is correct and also to smooth out the glue.
While the glue dried I cut a piece of foam board used for school displays to the size of the back. The board I had was white but I wanted the background black so I hot glued black construction paper to it. Take your box and trace the outer edge on the plexiglass while the plastic is still on it.
Cut out the door. Find where you want your hinges to be and mark the holes. The easiest way to attach the hinges to the plexi is to drill small holes where the screws will go. To do this take two pieces of tape and place them on the front and back of the plexiglass. This prevents the glass from cracking. Next drill a hole just smaller than the size of your screws. Next cut a piece of the aluminum and supper glue it to the bottom.
Make sure to overlap the bottom of the box. This will be your latch and handle. After the glue is dry you can paint your case. I painted it to match my picture frame but you can paint it to your liking. Next take a piece of magnet tape and put on the underside of the box and on the aluminum handle. This will seal your box. I then attached the hinges to to box. I also used a rotary tool and cut off wheel to cut the back of the screws off for a clean look.
If you want to add lighting you can now. I took a small led flash light and glued the top to the roof and ran the wires to a small battery pack and switch that is hidden behind the top of the box. Finally put your back on and glue it in with hot glue on the back. You can let it sit on a shelf or you can put hangers on the back to put it on the wall. Introduction: Cheap and Easy Display Case. By transforming vintage Follow.
More by the author:. About: I love to tinker. I enjoy making something out of nothing. More About transforming vintage ». Did you make this project? Share it with us! I Made It! Ant Decorations Light Up at Night. Langer 7 years ago on Introduction. Reply Upvote.